www.ams.com/AS5510
Revision 0.1
12 - 18
AS5510
Datasheet - Detailed Description
Figure 9. Data Read (Write Pointer, Then Read) - Slave Receive and Transmit
Automatic increment of address pointer. The AS5510 slave automatically increments the address pointer after each byte transferred.
The increase of the address pointer is independent from the address being valid or not.
Invalid Addresses. If the user sets the address pointer to an invalid address, the address byte is not acknowledged. Nevertheless a read or
write cycle is possible. The address pointer is increased after each byte.
Reading. When reading from a wrong address, the AS5510 slave returns all zero. The address pointer is increased after each byte. Sequential
read over the whole address range is possible including address overflow.
Write. A write to a wrong address is not acknowledged by the AS5510 slave, although the address pointer is increased. When the address
pointer points to a valid address again, a successful write accessed is acknowledged. Page write over the whole address range is possible
including address overflow.
7.4 SDA, SCL Input Filters
Input filters for SDA and SCL inputs are included to suppress noise spikes of less than 50ns. Furthermore the SDA line is delayed by 120ns to
provide an internal hold time for Start/Stop detection to bridge the undefined region of the falling edge of SCL. The delay needs to be smaller
than t
HD.STA
260ns. For Standard-mode and Fast-mode an internal hold time of 300ns is required, which is not covered by the AS5510 slave.
7.5 Register Map and Description
Table 8. Register Map
Register Address
Bit
Access
Type
7
6
5
4
3
2
1
0
00h
D7
D6
D5
D4
D3
D2
D1
D0
R
01h
OCF
Parity (even)
D9
D8
R
02h
Fast(0)
Slow mode (1)
Polarity(0)
PD(0)
R/W
03h
Offs7
Offs6
Offs5
Offs4
Offs3
Offs2
Offs1
Offs0
R/W
04h
Offs9
Offs8
R/W
05h
Reserved for factory testing
R/W
06h
07h
0Bh
Sens 1
Sens 0
R/W
S
1010110
0
A
XXXXXXXX
A
1010110
1
XXXXXXXX
A
S Start
SA Repeated Start
A Acknowledge (ACK)
Data transferred: X+1 Bytes + Acknowledge
NA Not Acknowledge (NACK)
Note: Last data byte is followed by NACK
P Stop
P
<Slave address>
<Word Address (n)>
<Slave Address>
<Data(n+1)>
XXXXXXXX
A
<Data(n)>
Sr
A
XXXXXXXX
NA
<Data(n+X)>
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATS137-PL-B-B
IC HALL SENSOR SGL 25MA SIP-3L
ATS177-PG-B-B
IC HALL SENSOR LATCH 25MA SIP-3L
ATS617LSGTN-T
IC HALL EFFECT GEAR SENSOR 4SIP
ATS625LSGTN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS627LSGTN-T
IC HALL EFFECT GEAR SENSOR 4-SIP
ATS635LSETN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS643LSHTN-I2-T
IC SENSOR GEAR TOOTH 4-SIP
ATS645LSHTN-I1
IC SENSOR GEAR TOOTH 4-SIP
相关代理商/技术参数
AS5510-DWLT-1K
功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5510-SO_EK_AB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:2.5 V ~ 3.6 V 嵌入式:- 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS5510-WL_EK_AB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:2.5 V ~ 3.6 V 嵌入式:- 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS5510-WL_EK_DB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS55110FLF
制造商:TT Electronics / IRC 功能描述:AS55110FLF
AS55110HLF
制造商:TT Electronics / IRC 功能描述:AS55110HLF
AS55110JLF
制造商:TT Electronics / IRC 功能描述:AS55110JLF
AS55111FLF
制造商:TT Electronics / IRC 功能描述:AS55111FLF